The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
Are you currently on the lookout for content about Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a new one is also a reasonably hard task. If the old tub is readily accessible, the project can relocate rapidly; if you need to open a wall to eliminate the old bathtub and position the new bath tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and set in the brand-new one. See to it you have actually qualified on your own for the task and also fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is better to consider employing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This short article will certainly aid you set up a brand-new bathtub in your bathroom if you have actually already purchased a brand-new tub and also do not require to change the plan of your previous water system pipelines.
Your devices as well as material list ought to comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be fairly problematic due to the restricted accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before carrying on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in place between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous type ought to be connected to the tap finishes first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using the two wood boards under its feet, put the tub in the needed position. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub up until the level reviews level.
To mount taps, fit all-time low of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Switch on the water as well as examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the bath tub should wait until the bathtub has been used at the very least when as this will settle it into its last position.
Preparing for the Setup
Firstly, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps device to stop stress on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to break a stiff seal, creating the water to pass through the wall surface between the bath and also the tiling, causing difficulties with wetness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealer can fracture fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very taken with How to Install a Bathtub and I'm hoping you liked my entry. Loved our blog? Please share it. Help someone else find it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Prioritize your plumbing; call us. Report this page